Pressure Conversion Calculator

Common Pressure Units

**PSI** (Pounds per Square Inch): Common in USA for refrigerant pressures, tire pressure, compressed air.

**kPa** (Kilopascal): SI unit (1000 Pascal), used internationally for HVAC specifications.

**bar**: Metric unit (100 kPa), common in Europe for refrigeration and compressed air.

**Pa** (Pascal): SI base unit, too small for most HVAC applications, but used in duct pressure calculations.

**in.wg** (Inches of Water Column/Gauge): Used for low pressures - duct static pressure, draft, fan curves.

**mmHg** (Millimeters of Mercury): Medical and vacuum applications, also called Torr.

**atm** (Atmosphere): Standard atmospheric pressure reference (14.696 psi).

**Conversion Factors**:

1\text psi = 6.895\text kPa = 0.06895\text bar = 6895\text Pa 1\text psi = 27.68\text in.wg = 51.71\text mmHg 1\text bar = 100\text kPa = 14.504\text psi 1\text atm = 14.696\text psi = 101.325\text kPa 1\text in.wg = 248.84\text Pa = 0.03613\text psi

Gauge vs Absolute Pressure

**Gauge Pressure** (psig, kPa(g), barg): Measured relative to atmospheric pressure. What pressure gauges read.

**Absolute Pressure** (psia, kPa(a), bara): Measured relative to perfect vacuum (zero pressure).

P_absolute = P_gauge + P_atmospheric

**Standard Atmospheric Pressure**: - 14.696 psia = 101.325 kPa - 1.01325 bar = 760 mmHg = 29.92 in.Hg

**Examples**:

1. Refrigerant pressure gauge reads 118 psig: - Absolute: 118 + 14.7 = 132.7 psia

2. Duct static pressure -1.2 in.wg: - Below atmospheric (negative gauge) - Absolute: 29.92 - 1.2/13.6 = 29.83 in.Hg(a)

3. Vacuum reading -28 in.Hg: - Absolute: 29.92 - 28 = 1.92 in.Hg(a) - Or: 1.92/29.92 × 14.7 = 0.94 psia

**When to Use Absolute**: - Thermodynamic calculations - Ideal gas law: PV = nRT - Pressure ratios - Saturation temperature lookup (refrigerants)

**When to Use Gauge**: - Field measurements - System pressures - Pressure drop calculations - Safety relief settings

Problem Context and Scope

Convert between psi, kPa, bar, Pa, in.wg, mmHg, atm, and other pressure units for HVAC applications In professional Hvac work, the same calculation appears in specifications, lab notebooks, spreadsheets, and compliance checks. The Pressure Conversion Calculator automates that relationship so you can focus on interpreting outcomes instead of re-deriving algebra. Scope includes typical textbook and field assumptions; exotic boundary conditions, non-standard materials, or regulatory overrides may require specialist review. Before trusting a number for safety-critical, medical, legal, or financial decisions, cross-check units, sign conventions, and whether your scenario matches the model intent described here.

Formula Derivation and Meaning

The calculator implements 1 psi = 6.895 kPa = 0.06895 bar = 27.68 in.wg. Each symbol corresponds to a physical, economic, or statistical quantity with implied units. Rearranging the expression highlights which inputs dominate: proportional terms scale linearly, ratios amplify sensitivity when denominators are small, and powers or roots change how uncertainty propagates. When multiple forms of the same law exist, use the version consistent with your reference tables and unit system. Document which variant you applied when sharing results with colleagues or reviewers so comparisons remain fair and reproducible across tools and spreadsheets.

1 psi = 6.895 kPa = 0.06895 bar = 27.68 in.wg

Input Parameters Explained

Key inputs include Input Pressure, Input Unit, Pressure Type. Enter values in the units shown beside each field; mixing systems without conversion is the most common source of large errors. Defaults and sliders reflect typical ranges but are not universal limits—extrapolating far beyond calibrated data may still return numbers while losing physical meaning. For select lists, choose the option that best matches your scenario even if labels are approximate. If an input is optional, leaving it blank may trigger built-in assumptions; read tooltips or descriptions when available. Sensitivity analysis—changing one input at a time—reveals which parameters deserve higher measurement precision.

Step-by-Step Calculation Procedure

First, gather measured or assumed values and convert them to the required units. Second, enter data in the Pressure Conversion Calculator form and confirm selections or toggles that alter the model branch. Third, submit the calculation and record the primary output together with any secondary metrics or charts. Fourth, sanity-check magnitude and sign: compare against order-of-magnitude estimates, limiting cases, or known benchmarks. Fifth, if results feed another equation, propagate uncertainty explicitly rather than treating intermediate values as exact. This workflow mirrors good laboratory and engineering practice and reduces the risk of publishing a correct formula with incorrect inputs.

Practical Applications

Typical uses include homework verification, quick feasibility checks, client estimates, and teaching demonstrations. Teams often run best, nominal, and conservative cases to bracket outcomes. In design iterations, automate repeated evaluations while varying one parameter across a sweep. In education, pair calculator output with hand-derived steps to build intuition. In operations, snapshot inputs and outputs for audit trails when regulations require traceability. Pair numerical results with charts when available to communicate trends to non-specialist stakeholders who may not read equations comfortably.

Common Mistakes and Troubleshooting

Watch for unit slips (meters versus feet, percent versus decimal), sign errors (compression versus tension, income versus expense), off-by-one period choices (monthly versus annual rates), and using stale constants. If results look surprising, re-check input order, whether angles are in degrees or radians, and whether the tool expects absolute or gauge values. Compare with a second method or tabulated example when possible. Large discontinuities often indicate crossing a domain threshold coded in the implementation—review piecewise rules. When exporting to spreadsheets, lock cell references so later edits do not silently break linked formulas.

Accuracy, Limitations, and Validation

Displayed precision may exceed real-world accuracy. Report only the significant figures justified by your input quality. The model may assume ideal conditions—uniform properties, steady state, linear response, perfect markets, or representative samples—that real systems violate. Validate against measured data when stakes are high. Document temperature, pressure, humidity, sample size, or market regime if they influence constants. For regulated industries, cite the code edition or standard you followed. Treat online tools as aids, not replacements for professional judgment where codes mandate licensed review.

Related Concepts and Extensions

Adjacent topics often include dimensional analysis, uncertainty propagation, inverse problems (solving for an input given a target output), and optimization under constraints. Exploring related calculators on the same topic helps build a coherent workflow—for example, converting units before using this tool, or feeding its output into a downstream capacity check. Advanced users may implement custom scripts that batch-evaluate the same relationship across parameter grids. Students benefit from plotting dependent variables versus one input while holding others fixed, reinforcing calculus and physical intuition beyond a single numeric answer.

Worked Example

Inputs

• inputPressure: 100
• inputUnit: psi
• pressureType: gauge

Result: 100 psig = 689.5 kPa(g) = 6.895 bar(g) = 114.7 psia = 2768 in.wg

Explanation

Converting 100 psig to various units:

**To kPa**: 100 × 6.895 = 689.5 kPa(g)

**To bar**: 100 × 0.06895 = 6.895 bar(g)

**To Pascal**: 100 × 6895 = 689,500 Pa(g)

**To in.wg**: 100 × 27.68 = 2,768 in.wg

**To mmHg**: 100 × 51.71 = 5,171 mmHg

**To Absolute Pressure**: 100 + 14.696 = 114.696 psia 689.5 + 101.325 = 790.8 kPa(a) 6.895 + 1.01325 = 7.908 bar(a)

**HVAC Context**: 100 psig is typical for: - R-22 liquid line pressure (moderate conditions) - Compressed air systems - Chiller condenser water pressure - Boiler operating pressure (low-pressure steam)

Second Scenario

Inputs

• inputPressure: 126
• inputUnit: psi
• pressureType: gauge

Result: 100 psig = 689.5 kPa(g) = 6.895 bar(g) = 114.7 psia = 2768 in.wg

Explanation

This scenario uses different inputs (inputPressure = 126, inputUnit = psi, pressureType = gauge) to show how changing one variable affects the pressure conversion result. Run the calculator above with these values to get the exact updated output with step-by-step work.